Photo booth software..

[sze1009]

kung CIS printer gamit nyo try nyo cdrking meron mura photopaper or sa http://cis.thenet.ph.
I'm using DNP printer cost 5.70php per print.

• Tweet

[eos_kiss]

I'm using DNP printer cost 5.70php per print.

Sir anong model itong DNP and do have a link to their website?

Salamat!

• Tweet

[sze1009]

Sir anong model itong DNP and do have a link to their website?

Salamat!

http://www.imagingspectrum.com/dnp-ds40-dye-sub_printer-ds40.html

• Tweet

[tux072]

Sir EOS_Kiss.. saan niyo nabili yung printer?  me local distributor ba dito sa pinas? and also handles warranty support? TIA.

• Tweet

[jopetdt]

guys, patulong naman.. I have 2 selphy CP760's and im using breezesys and my os is vista..
you have any ideas what software I can use para pwede ko distribute yung print jobs sa dalawang selphys? thanks!

• Tweet

[sze1009]

guys, patulong naman.. I have 2 selphy CP760's and im using breezesys and my os is vista..
you have any ideas what software I can use para pwede ko distribute yung print jobs sa dalawang selphys? thanks!

para sa dual printing...
http://www.frogmorecs.com/printdistributor

• Tweet

[qop]

sir japeeps magkano ang ink ng printer mo? baka ganyan lang rin gamitin ko, very high ang demand ng Sephy, nagkakaubusan na. 

• Tweet

[nickster]

@sze1009

dun sa frogmore software mo ba, naka check yung 'spool prints' na box?

yung setup ko kasi, by the time ready na magprint ng next pic, idle na ulit si printer#1, so hindi umaabot kay printer#2. dapat ba automatic na alternate yung printing kahit na walang pending?

• Tweet

[jopetdt]

@sze1009

dun sa frogmore software mo ba, naka check yung 'spool prints' na box?

yung setup ko kasi, by the time ready na magprint ng next pic, idle na ulit si printer#1, so hindi umaabot kay printer#2. dapat ba automatic na alternate yung printing kahit na walang pending?

ano po OS gamit nyo and printer? yung akin po kasi, pag magpprint na ko, parang hindi nakikita nung program yung virtual printer na ginawa ko.. im using breezesys

• Tweet

[jopetdt]

guys! just solved my dual printing dilemma.. and I didn't use any third party software..

I just installed the driver of my printer (in this case i have 2 canon selphy cp760's)

after that, I did the following:

Control Panel > Printers > Right-click on the printer driver and chose properties > Went to the Ports tab and checked the box for "Enable Printer Pooling" > checked the the box for the other printer I wanted to use and that's it!!!

hope this helps..

• Tweet

[sze1009]

@sze1009

dun sa frogmore software mo ba, naka check yung 'spool prints' na box?

yung setup ko kasi, by the time ready na magprint ng next pic, idle na ulit si printer#1, so hindi umaabot kay printer#2. dapat ba automatic na alternate yung printing kahit na walang pending?

no need to check the spool prints,
sa virtual printer mo unchecked the enable bidirectional port.

• Tweet

[Nizhots]

Mga sir, planning ko rin po magtayo nito sa province namin although konti lang ang me ganito dito, saka magandang alternatibo ito sa Internet cafe. Thanks po sa lahat nang bigay ng idea.

Pwede rin pong gamitin yung low watts na Spotlight na mabibili sa ace hardware?

thanks

• Tweet

[jilliepot]

im using ip3680 prints 49secs per 4r prints got it for less than 5k sa canon
you cah also use ip4680 around 20sec per print less than 7k not sure.
or printers from aperture Hiti can print 9 sec per 4r prints kaso sobrang mahal.

sir japeeps, magkano po yung ink nung ip4680? tia.

• Tweet

[sze1009]

Mga sir, planning ko rin po magtayo nito sa province namin although konti lang ang me ganito dito, saka magandang alternatibo ito sa Internet cafe. Thanks po sa lahat nang bigay ng idea.

Pwede rin pong gamitin yung low watts na Spotlight na mabibili sa ace hardware?

thanks

ibig mong sabihin hindi ka na gagamit ng flash? sportlight ang gagamitin mo sa lighting mo?

• Tweet

[japeeps]

around 7k yata yun...

+1.. parang di magiging effective and spot light dapat flash

• Tweet

[flxrms]

flash and continuous light basically have the same output...light, they may differ with their temperature, white balance or the quality of light but then again..its still light..as long as exposure is correct it should work fine...gamit ka nalang ng lightmeter.

• Tweet

[jjdee]

guys! just solved my dual printing dilemma.. and I didn't use any third party software..

I just installed the driver of my printer (in this case i have 2 canon selphy cp760's)

after that, I did the following:

Control Panel > Printers > Right-click on the printer driver and chose properties > Went to the Ports tab and checked the box for "Enable Printer Pooling" > checked the the box for the other printer I wanted to use and that's it!!!

hope this helps..

sir jopet! ask ko lang if you have same selphy but different models? will this still works? thanks in advance sir.. 

• Tweet

[picture easy]

sir patulong po... bago lang po sa photobooth busines. ano po ba maganda setup ng lights para sa photobooth?

• Tweet

[picture easy]

sir jappeeps salamat sa mga replys nio malaking tulong sa mga nagsisimula palang tulad ko. yung software nga po pala pano magpurchased?

• Tweet

[japeeps]

No prob.
sa webiste lang.. download the software and purchase the license...

For the lights im using simock e300 since im also using it for model shoot..
pwede na siguro ung jinbei na tag 16k sa aperture

• Tweet